How to Restart Into BIOS (UEFI) From Windows 11

You need to switch on virtualization or change the boot order, but the PC starts so fast that pressing a key at power-on never works. Windows 11 can restart straight into BIOS (UEFI) setup for you: go to Settings > System > Recovery, select Restart now next to Advanced startup, then choose Troubleshoot > Advanced options > UEFI Firmware Settings > Restart. A one-line command does the same thing.

Before You Restart Into Firmware

BIOS and UEFI are both names for the firmware that runs before Windows loads. Most current PCs use UEFI, but menus, manuals and PC makers still say “BIOS,” so this article uses both terms. The firmware setup screen is where boot order, virtualization support, Secure Boot and similar hardware options live.

Do three things first:

  1. Save your work. Every method here restarts the PC, and a shutdown command with a countdown forces open apps to close.
  2. Find your BitLocker recovery key. Microsoft’s Windows Recovery Environment page notes that an encrypted device needs the recovery key for certain recovery tools. Changing boot or security settings in firmware can also make BitLocker ask for the key at the next startup. If you signed in with a Microsoft account, Microsoft says the key is usually stored at aka.ms/myrecoverykey; work or school devices keep it with your organization. Microsoft’s page on finding your BitLocker recovery key lists every place to look.
  3. Write down what you plan to change. Note the current setting before you touch it, so you can put it back.

If you’re planning a firmware update rather than a settings change, Microsoft’s BitLocker recovery overview lists BIOS or UEFI firmware upgrades as a recovery trigger and recommends suspending BitLocker first. Suspended protection resumes automatically after the restart unless you set a reboot count. To turn encryption off entirely instead, see turning off BitLocker in Windows 11.

Restart Into UEFI From Settings

This is the most reliable route because you never have to time a key press.

  1. Open Settings (press Windows key + I).
  2. Select System, then Recovery.
  3. Under Recovery options, find Advanced startup and select Restart now. Confirm if Windows asks.
  1. On the blue “Choose an option” screen, select Troubleshoot.
  2. Select Advanced options.
  3. Select UEFI Firmware Settings, then Restart.

The PC restarts and opens the firmware setup screen. Its look depends on the PC or motherboard maker. The blue menu in steps 4 to 6 is the Windows Recovery Environment (WinRE), the same place you use for startup repair and Safe Mode; booting into recovery mode in Windows 11 covers its other tools.

Use Shift + Restart

If Settings won’t open, or you’re at the sign-in screen, you can reach the same blue menu another way. Microsoft describes it as holding the Shift key while you select Power > Restart.

  1. Open the Start menu, or go to the sign-in screen.
  2. Select the Power button.
  3. Press and hold Shift, then select Restart. Keep holding Shift until the “Please wait” or blue menu appears.
Illustration pairing the Shift key with Restart in the Windows Power menu
Illustration showing how to hold Shift while selecting Restart in the Windows Power menu.
  1. Choose Troubleshoot > Advanced options > UEFI Firmware Settings > Restart.

If the PC restarts normally, you let go of Shift too soon. Try again and hold it a little longer. For ordinary restarts and the other ways to trigger one, see how to restart Windows 11.

Restart Straight Into Firmware With a Command

The shutdown command can skip the blue menu entirely. Microsoft’s shutdown command reference says the /fw option, combined with a shutdown option, makes the next restart go to the firmware user interface.

  1. Save and close your work.
  2. Right-click the Start button and open Terminal (Admin) (the label may read Windows Terminal (Admin) on some versions). Dell’s instructions for this method use an administrator Command Prompt, so running it elevated avoids problems.
  3. Type shutdown /r /fw /t 0 and press Enter.
Firmware restart command with its restart, firmware, and timeout options explained
Command guide. Save your work before running the command in an elevated terminal.

What each part does, per Microsoft’s reference:

SwitchMeaning
/rRestart after shutting down
/fwSend the next restart to the firmware screen (needs a shutdown option such as /r)
/t 0Wait zero seconds. Without /t, the default wait is 30 seconds. Any value above 0 also forces apps to close, which can lose unsaved data.
/a /fwCancel a pending shutdown and clear any pending boot to firmware

Changed your mind during the countdown? Run shutdown /a /fw before the timer ends.

If you visit firmware often, for example on a test machine where you switch boot order for different USB drives, make a shortcut: right-click the desktop, select New > Shortcut, enter shutdown /r /fw /t 0 as the location, and name it “Restart to UEFI.” Right-click the shortcut, open Properties, select Advanced, and check Run as administrator.

If UEFI Firmware Settings Is Missing

Sometimes Advanced options shows Startup Repair, Startup Settings and the rest, but no UEFI Firmware Settings tile. A likely cause is that Windows was installed in legacy BIOS mode (often shown in firmware as CSM or Legacy) rather than UEFI mode. Microsoft’s UEFI and legacy BIOS boot mode page explains that installed Windows starts in the mode it was installed in, so the tile and the /fw switch generally aren’t offered on a legacy install. In that case the command may fail with an error.

Your options then:

  • Use the startup key at power-on (next section).
  • Check the firmware type in System Information (search for msinfo32) under BIOS Mode, if it’s shown on your PC. Checking your BIOS version uses the same window.
  • Converting a legacy install to UEFI is possible with Microsoft’s MBR2GPT tool, but that’s a bigger job than this article covers.

Use the Startup Key Instead

Every PC also has a key that opens setup during power-on. The same Microsoft boot mode page lists common ones: Esc, Delete, F1, F2, F10, F11 or F12, depending on the maker. The full list of maker keys, plus tips for timing the press, is in how to enter BIOS or UEFI settings in Windows 11.

Fast startup may be one reason the key press gets missed: with it on, Windows doesn’t fully shut down, so choosing Restart instead of Shut down can help, or you can disable fast startup in Windows 11.

Leave Setup Without Breaking Anything

  • Change one setting at a time, then save and test it in Windows.
  • Use the setup screen’s “Save and Exit” (often F10, shown at the bottom of most setup screens) when you want to keep a change, or “Exit Without Saving” (sometimes “Discard Changes and Exit”) when you only looked around.
  • If Windows won’t start after a change, go back into setup with the startup key and restore the value you wrote down, or use the “Load Defaults” option your firmware offers.
  • If you only need to boot once from a USB drive, the one-time boot menu is gentler than changing the permanent boot order. See opening the boot menu in Windows 11.

BIOS and UEFI Restart Questions

Does opening firmware setup delete files or change anything?

Not by itself. Opening the setup screen and leaving without saving doesn’t change your files or settings. Risk comes from the changes you save, which is why one change at a time is the safer habit.

Why did BitLocker ask for a key after I left setup?

Microsoft lists changes to boot settings and firmware among the events that can trigger BitLocker recovery. Enter the 48-digit recovery key from your Microsoft account or your organization so Windows can open the drive and continue starting.

Can I restart a remote PC into firmware?

The shutdown command can target another computer with the /m switch, but the setup screen appears on that PC’s own display, so someone needs to be in front of it to make changes.

Is the Windows 10 route different?

Only the first part. On Windows 10 the Advanced startup button is under Update & Security > Recovery. From the blue menu onward, the steps match.

Once you’re in setup, make the one change you came for, such as turning on virtualization support, then save, exit and confirm the result in Windows before changing anything else.